로그인을 해주세요.

제품정보

TMS & 연돌배출가스 굴뚝 배출가스 분석장치 ENDA-5000Series

페이지 정보

profile_image
작성자 최고관리자
댓글 0건 조회 39회 작성일 22-05-18 13:19

본문

제품명 굴뚝 배출가스 분석장치 ENDA-5000Series

제품설명


개요

10 만대가 넘는 판매 대수와 30년 이상의 실적을 기반으로 설개된 굴뚝배출가스 분석장치인 ENDA-5000Series. 연속 측정에 탁월한 전처리 장치는 물론 장기적인 안정성이 있는 Cross Modulaion방식의 NDIR(NOx,SO2,CO,CO2) 및 MPA(O2) 를 적용하였습니다.그리고, 터치화면을 갖추어 각종 설정을 간단히 조작할수 있어서 유지보수작업의 효율을 높였습니다.환경관리공단의 요구에 부합한 DIGITAL 전송이 가능하며, 연속감시가 필요한 보일러 배기가스 , 소각장 , 전력 발전소 등 다양한 곳에 적용이 가능합니다.

기능

  • 1대로 5성분을 동시 연속측정

            ENDA-5000Series는 HORBA독자의 광학계로 5성분을 1대로 측정이

            가능합니다. 5가지의 측정 성분을 자유롭게 조합할수 있습니다.

  •  간섭영향을 큰 폭으로 감소

         간섭보정형검출기, HORIBA독자적인 간섭 Filter로 인해 큰폭으로

         간섭가스영향을 줄였습니다.

  • DIGITAL 전송

          한국환경관리공단의 요구에 부합하는 DIGITAL 전송을 지원합니다.

  • SO2의 교정 시간을 대폭 단축 

         SO2의 교정은 기존 Wet기준의 교정에 의하여, 장시간(약15분)이 필요로

         하였으나  Dry기준 교정법을 채용하여 약 3분으로 단축하였습니다.



사양

Model

ENDA-5000

Component

NOx

SO2

CO

CO2

O2*1

Measurement methods

NDIR

NDIR

NDIR

NDIR

Magneto-pneumatic detection

Range*2

Standard

200~5000 ppm

200~5000 ppm

200~5000 ppm

5~25 vol%

10~25 vol%

 

Optional

100 ppm~

50 ppm~

100 ppm~

-

-

Range Ratio

Within a factor of 10

Within a factor of 10

Within a factor of 10

Within a factor of 5

Within a factor of 2.5

Repeatability

Within 0.5% of full scale (with optional range, or during O2 measurement, ±1.0% of full scale)

Linearity (indicator error)

±1.0% of full scale

Zero drift

±1.0% of full scale (assuming surrounding temperature is maintained within 5 °C)
(with optional range, or O2 measurement, ±2.0% of full scale)

Span drift

±2.0% of full scale/week (assuming surrounding temperature is maintained within 5°)

Response time*3

Within 60 seconds (Td + T90 from equipment intake area) (sample flow 0.6 L/min.) (within 240 seconds for SO2 only)

Overall interference frrom co-existing gases

±2.0% of full scale/week (within standard range, with standard gas formation)

Display

Touch panel LCD (backlight) (four usable lines)

Environment
Condition

Temperature

-5 to 40 °C (away from direct sunlight and radiation heat )*4

Humidity

85% or less (no condensation)

Vibration

100 Hz, 0.3 m/S2 or less

Dust

Standard environment or better

Measuring Gas Condition

Temperature

250 °C or lower

Dust

0.1 g/Nm3 or less

Standard gas composition*5

NO: 500 ppm or less; NO2: 15 ppm or less; SO2: 1000 ppm or less; SO3: 50 ppm or less;
CO: 200 ppm or less; CO2: 15% volume or less; H2O: 40% volume or less

Sampling method

Dry sampling using an electric cooler

Sample gas flow

2.5 L/min~3.0 L/min

Sample inlet tube

Teflon tubing (Ø8/Ø6 mm)

Sample gas pressure

±4.9 kPa (three points selected)
(with no sample gas back pressure)

(1) -1.96 to 4.9 kPa
(2) ±3.43 kPa
(3) -4.9 to 1.96 kPa

 

Pressure control

Pressure control uses a regulator and cylinder; Reduced pressure sampling; Control pressure: -4.9 kPa

Output

DC 4 to 20 mA (absolute output) (DC 0 to 16 mA/DC 0 to 1 V/DC 1 to 5V optional) Max. 12 output systems

External output

Analysis alerts, analysis warnings, range display, corrections, conservation, purging (option)
Contact capacity: DC 30 V 1 A, AC 250 V 1 A resistance load

Correction method

Dry correction, automatic correction (correction cycle: 7 days standard, can be adjusted to between 1 and 99 days), manual correction

Calibration gas

Zero gas

With measurement method authorization: N2, When there is no measurement method authorization: N2 or ambient air

O2 carrier gas

Ambient air

Span gas

Gas cylinder for each component measured (when there is no measurement method authorization: O2 or ambient air can be used)

Probe collection point filter

Flange: JIS 10K, 40 AFF; Sample probe tube length: 1000 mm; Material: SUS-316 stainless steel;
Filter element: SUS-304 stainless steel and 2um-pleated quartz wool; Electric heater: 100 VA, with water droplet proof case

Power supply

AC 100 V ±15 V(85 V~115 V)

Power frequency

50/60 Hz (switchable)

Power consumption

About 800 VA (heated piping 30m: +1100 VA; heater in tray: +300 VA)

Exterior dimensions/Mass

600 (W) x 1770 (H) x 300 (D) mm (high pressure gas cylinders, 3.4 L cylinders, maximum of 3 cylinders); About 180 kg (not including cylinders)
600 (W) x 1770 (H) x 300 (D) mm (high pressure gas cylinders, 3.4 L cylinders, maximum of 3 cylinders); About 200 kg (not including cylinders)

Materials in contract with sample gas

SUS-316 stainless steel, SUS-304 stainless steel, Teflon, polypropylene, polyethylene,
flourorubber, PVC, PVDF, and glass

Enclosure

Independent outdoor installation
Plate thickness: Main unit, doors, top plate, steel plate: 2.3 mm; Channel base: 3.2 mm; Doors: front opening; Interface: right front

Color/Finish

Semi-gloss Munsell 5Y7/1 on all inner and outer surfaces